MC9S08PA60VLD Datasheet PDF – S08 Microcontroller IC 8-Bit 20MHz 60KB (60K x 8) FLASH 44-LQFP (10x10)

Product Overview

MC9S08PA60VLD Images are for reference only:

Product Specifications

MC9S08PA60VLD Datasheet PDF Download:

MCU block diagram

Features

• 8-Bit S08 central processor unit (CPU)

– Up to 20 MHz bus at 2.7 V to 5.5 V across temperature range of -40 °C to 105 °C

– Supporting up to 40 interrupt/reset sources

– Supporting up to four-level nested interrupt

– On-chip memory

– Up to 60 KB flash read/program/erase over full operating voltage and temperature

– Up to 256 byte EEPROM; 2-byte erase sector; program and erase while executing flash

– Up to 4096 byte random-access memory (RAM)

– Flash and RAM access protection

• Power-saving modes

– One low-power stop mode; reduced power waitmode

– Peripheral clock enable register can disable clocks to unused modules, reducing currents; allows clocks to remain enabled to specific peripherals in stop3 mode

• Clocks

– Oscillator (XOSC) - loop-controlled Pierce oscillator; crystal or ceramic resonator range of 31.25 kHz to 39.0625 kHz or 4 MHz to 20 MHz

– Internal clock source (ICS) - containing a frequencylocked-loop (FLL) controlled by internal or external reference; precision trimming of internal reference allowing 1% deviation across temperature range of 0 °C to 70 °C and 2% deviation across temperature range of -40 °C to 105 °C; up to 20 MHz

• System protection

– Watchdog with independent clock source

– Low-voltage detection with reset or interrupt; selectable trip points

– Illegal opcode detection with reset

– Illegal address detection with reset

• Development support

– Single-wire background debug interface

– Breakpoint capability to allow three breakpoints setting during in-circuit debugging

– On-chip in-circuit emulator (ICE) debug module containing two comparators and nine trigger modes.

• Peripherals

– ACMP - one analog comparator with both positive and negative inputs; separately selectable interrupt on rising and falling comparator output; filtering

– ADC - 16-channel, 12-bit resolution; 2.5 µs conversion time; data buffers with optional watermark; automatic compare function; internal bandgap reference channel; operation in stop mode; optional hardware trigger

– CRC - programmable cyclic redundancy check module

– FTM - three flex timer modulators modules including one 6-channel and two 2-channel ones;

16-bit counter; each channel can be configured for input capture, output compare, edge- or centeraligned PWM mode

– IIC - One inter-integrated circuit module; up to 400 kbps; multi-master operation; programmable slave address; supporting broadcast mode and 10-bit addressing; supporting SMBUS and PMBUS

– MTIM - Two modulo timers with 8-bit prescaler and overflow interrupt

– RTC - 16-bit real timer counter (RTC)

– SCI - three serial communication interface (SCI/UART) modules optional 13-bit break; full duplex non-return to zero (NRZ); LIN extension support

– SPI - one 8-bit and one 16-bit serial peripheral interface (SPI) modules; full-duplex or single-wire bidirectional; master or slave mode

• Input/Output

– Up to 57 GPIOs including one output-only pin

– Two 8-bit keyboard interrupt modules (KBI)

– Two true open-drain output pins

– Eight, ultra-high current sink pins supporting 20 mA source/sink current

• Package options

– 64-pin LQFP; 64-pin QFP

– 48-pin LQFP

– 44-pin LQFP

– 32-pin LQFP

Other data sheets within the file:

Datasheet
MC9S08PA60 Series DataSheet
MC9S08PA60 Ref Manual