Product Overview
Product Category: | Memory - Configuration Proms for FPGA's |
Kynix Part #: | KY32- EPCS1SI8N |
Manufacturer Part#: | EPCS1SI8N |
Manufacturer | Altera |
Description: | IC CONFIG DEVICE 1MBIT 8SOIC |
Package: | SOP8 |
Datasheet: | |
Stock: | Yes |
Quantity: | 256190 PCS |
EPCS1SI8N Images are for reference only:
Product Specifications
Product Category | Memory - Configuration Proms for FPGA's |
Manufacturer | Altera |
Series | EPCS |
Packaging | Tube |
Package/Case | 8-SOIC (0.154", 3.90mm Width) |
Architecture | Sectored |
Boot Block | No |
Block Organization | Symmetrical |
Command Compatible | No |
China RoHS Compliant | Yes |
Clock Frequency-Max | 20.0 MHz |
Endurance | 100000.0 Write/Erase Cycles |
ECC Support | No |
EU RoHS Compliant | Yes |
Frequency | 20 MHz |
Interface Type | Serial |
JESD-30 Code | R-PDSO-G8 |
JESD-609 Code | e4 |
Lead Shape | Gull-wing |
Memory Size | 128 kB |
Memory Type | FLASH |
Memory Width | 1 |
Memory Density | 1048576.0 bit |
Memory IC Type | CONFIGURATION MEMORY |
Mounting-Style | SMD/SMT |
Mounting-Type | Surface Mount |
Moisture Sensitivity Level | 3 |
Maximum-Operating-Frequency | 40 MHz |
Number of Pins | 8 |
Number of Words | 1048576.0 |
Number of Words Code | 1 M |
Number of Terminals | 8 |
Number of Functions | 1 |
Organization | 1MX1 |
Operating Mode | SYNCHRONOUS |
Operating Temperature-Min | -40 °C |
Operating Temperature-Max | 85.0°C |
Operating Supply Current | 50 uA |
Page Size | 256 byte |
Package Body Material | PLASTIC/EPOXY |
Package Code | SOP |
Package Equivalence Code | SOP8,.25 |
Package Shape | RECTANGULAR |
Package Style | SMALL OUTLINE |
Parallel/Serial | SERIAL |
Peak Reflow Temperature | 260 °C |
Pin Count | 8 |
PCB changed | 8 |
Programmability | Yes |
Product Type | FPGA - Configuration Memory |
Sector Size | 32 Kbyte x 4 |
Seated Height-Max | 1.75 mm |
Sub Category | Flash Memories |
Supply Current-Max | 0.015 Amp |
Supplier Device Package | 8-SOIC |
Standby Current-Max | 5.0E-5 Amp |
Supply Voltage-Nom | 3.3 V |
Supply Voltage-Min | 3.0 V |
Supply Voltage-Max | 3.6 V |
Surface Mount | Yes |
Type | NOR TYPE |
Tradename | Enpirion |
Technology | CMOS |
Timing Type | Synchronous |
Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
Terminal Form | GULL WING |
Terminal Pitch | 1.27 mm |
Terminal Position | DUAL |
Temperature Grade | INDUSTRIAL |
Time@Peak Reflow Temperature-Max | 30 s |
Height | 1.65(Max) |
Length | 4.9 mm |
Width | 3.9 mm |
Unit Weight | 0.006173 oz |
Voltage - Supply | 2.7V ~ 3.6V |
RoHS Compliant | Yes |
Lead Free Status | Lead Free |
EPCS1SI8N Datasheet PDF Download:
Block Diagram
Description
To configure a system using an SRAM-based device, each time you power on the device, you must load the configuration data. The EPCS device is a flash memory device that can store configuration data that you use for FPGA configuration purpose after power on. You can use the EPCS device on all FPGA that support AS x1 configuration scheme.
For an 8-pin SOIC package, you can migrate vertically from the EPCS1 device to the EPCS4 or EPCS16 device. For a 16-pin SOIC package, you can migrate vertically from the EPCS64 device to the EPCS128 device.
With the new data decompression feature supported, you can determine using which EPCS device to store the configuration data for configuring your FPGA.
Features
■ Supports active serial (AS) x1 configuration scheme
■ Easy-to-use four-pin interface
■ Low cost, low pin count, and non-volatile memory
■ Low current during configuration and near-zero standby mode current
■ 2.7-V to 3.6-V operation
■ EPCS1, EPCS4, and EPCS16 devices available in 8-pin small-outline integrated circuit (SOIC) package
■ EPCS64 and EPCS128 devices available in 16-pin SOIC package
■ Enables the Nios processor to access unused flash memory through AS memory interface
■ Reprogrammable memory with more than 100,000 erase or program cycles
■ Write protection support for memory sectors using status register bits
■ In-system programming (ISP) support with SRunner software driver
■ ISP support with USB-Blaster, EthernetBlaster, or ByteBlaster II download cables
■ Additional programming support with the APU and programming hardware from BP Microsystems, System General, and other vendors
■ By default, the memory array is erased and the bits are set to 1
Other data sheets within the file:
Datasheet | |
EPCS1SI8N Datasheet | ![]() |